GRIPEDIA FIELD GUIDE β’ Stands & Support Systems β’ HOLLYWOOD, CALIFORNIA, USA
Combo, Mombo & High Roller Stands: Heavy Overhead Support Systems
Why Combo vs. High Roller vs. Mombo architectures differ, 1-1/8 inch Junior receivers vs. Pop-up Baby pins, leveling leg physics, and the 2025 Lifetime Warranty.
Direct Field Answer: Combo, High Roller, and Mombo Stands step in whenever payloads exceed a 40" C-Stand's torque limit or reach heights above 10 ft. Every heavy Norms steel stand pairs a dual 1-1/8" Junior receiver + pop-up 5/8" Baby pin with Leveling ("Rocky Mountain") Leg geometry, and all new Grip Stands manufactured in 2025 and afterwards carry the industry's First-Ever Lifetime Warranty.
1. Norms Heavy Steel Stand Tier Comparison
| Stand Class | Representative SKU | Riser Tiers | Leg Style | Signature Production Application |
|---|---|---|---|---|
| Low Boy Combo Walker / Roller | GST-SSVTL-2W3 / 2R1 | 2-Riser Heavy Steel | Walker / Locking Caster | Ultra-low center of gravity under 4Γ4 floppies & heavy HMIs |
| Sky High Combo Walker (2R / 3R) | GST-SACTS-2W1 / 3W1 | 2-Riser / 3-Riser | Square Steel Leveling | Versatile location & studio key stand up to 14β15 ft |
| 16'β20' High Roller Stands | GST-HSVMS-3R1 / MT / MH | 3-Riser Heavy Steel | Locking Pneumatic / Swivel Wheel | Rolling studio & stage towers for 12Γ12 frames & 18K HMIs |
| Mombo Combo Walker (4R) | GST-HSVMM-4W4 | 4-Riser Reinforced | Heavy Wide-Footprint + Guy Ears | 20β24 ft outdoor 20Γ20 butterfly elevation |
2. Diagram: Combo Head & Triple-Riser Load Path
3. Field Elevation Rules for Heavy Stands
- Leveling Leg Downhill: When pitching on driveways or bleachers, loosen the sliding collar on the single Leveling Leg and extend it downhill so the main column stands vertical by bubble levelβnever lean the center mast.
- Earliest Riser First (or Top-Down Rigging): Always attach lamps and 4-1/2" Lollipops (
GSA-GAPLJ-400) at chest height before raising risers sequentially, keeping center of gravity tight and leaving at least 4β6 inches of telescoping overlap inside each collar. - Never Roll Tall Risers Unattended: Lock every caster brake on High Rollers before walking away, and never wheel an extended 3-riser stand across doorway thresholds or cable ramps without lowering risers first.
Hardware Engineered for This Rigging Standard
Frequently Asked Set Questions
Q: What makes a Combo Stand a 'Combo' stand?
Its dual-purpose Combo Head houses a recessed 1-1/8 inch (28mm) Junior female receiver combined with a spring-locked pop-up 5/8 inch (16mm) Baby male stud, allowing crews to rig either Junior fixtures or Baby hardware cleanly.
Q: What is the key difference between a Triple-Riser Combo Stand and a Mombo Combo Stand?
A standard Sky High Combo reaches ~14 to 15 feet with a 4-foot footprint, whereas a Norms 4-Riser Mombo Combo pushes beyond 20 to 24 feet with reinforced heavy-wall square steel legs, oversized 4-inch caster sockets, and dedicated guy-wire ears for 20x20 overheads.
Q: Are new Norms Combo and High Roller Stands covered by the Lifetime Warranty?
Yes. Introduced in 2025 under Tony and Terry, the First-Ever Lifetime Warranty applies to all new Norms Grip Stands manufactured in 2025 and afterwards.
VERIFIED IN HOLLYWOOD, CALIFORNIA, USA β’ EST. 1962
Combo, Mombo & High Roller Stands: Heavy Overhead Support Systems